User Tools

Site Tools


playground:startup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
playground:startup [2012/06/01 10:25]
carter
playground:startup [2017/04/17 11:41] (current)
jacobs
Line 1: Line 1:
 ====== Accelerator Start-up ====== ====== Accelerator Start-up ======
  
-1. **Initial Machine Voltage setup:**+1. **Verify ​Initial Machine Voltage setup:**
  
 Initial conditions on TPS: Initial conditions on TPS:
Line 28: Line 28:
  
  
-a.  Switch the POWER SUPPLIES to ON, the yellow light should come on. Switch CHAIN MOTORS to ON, lights 1, 2, and 3 should all come on.  Begin to increase the CHARGING VOLTAGE ​ while observing the TERMINAL VOLTAGE and the GRID VOLTAGE. ​ DO NOT allow the GRID VOLTAGE to become more negative than   -10 VDC.  ​+a.  Switch the POWER SUPPLIES to ON, the yellow light should come on. Switch CHAIN MOTORS to ON, lights 1, 2, and 3 should all come on.  Begin to increase the CHARGING VOLTAGE ​ while observing the TERMINAL VOLTAGE and the GRID VOLTAGE. ​ DO NOT allow the GRID VOLTAGE to become more negative than   **-5** VDC.  ​
  
-b. Continue to increase the CHARGING VOLTAGE until you reach the approximate TERMINAL VOLTAGE **__OR__** until the GRID VOLTAGE reaches ​ -10 VDC, **__THEN__** proceed to step 2:+b. Continue to increase the CHARGING VOLTAGE until you reach the approximate TERMINAL VOLTAGE **__OR__** until the GRID VOLTAGE reaches  ​**-5** VDC, **__THEN__** proceed to step 2:     (The GRID VOLTAGE may never reach -5 VDC when running at ultra low Terminal energy, E < 0.300 MV, do the best you can)
  
  
Line 36: Line 36:
 **2. Corona Probe Adjustment** **2. Corona Probe Adjustment**
  
-FYI:  The CORONA PROBE CURRENT will rise until it reaches the value set by the BIAS CURRENT. ​ After that, the GRID VOLTAGE will change to keep the CORONA PROBE CURRENT at the set value. ​ The goal is to balance the UPCHARGE and CORONA PROBE POSITION so that you have the desired TERMINAL VOLTAGE and -10 VDC on the GRID VOLTAGE. ​ Do (a) or (b) as needed:+FYI:  The CORONA PROBE CURRENT will rise until it reaches the value set by the BIAS CURRENT. ​ After that, the GRID VOLTAGE will change to keep the CORONA PROBE CURRENT at the set value. ​ The goal is to balance the UPCHARGE and CORONA PROBE POSITION so that you have the desired TERMINAL VOLTAGE and **-5** VDC on the GRID VOLTAGE. ​ Do (a) or (b) as needed:
  
 a. Move the CORONA PROBE POSITION “IN” to make the GRID VOLTAGE more negative. ​ This may require you to adjust the UPCHARGE to maintain TERMINAL VOLTAGE. a. Move the CORONA PROBE POSITION “IN” to make the GRID VOLTAGE more negative. ​ This may require you to adjust the UPCHARGE to maintain TERMINAL VOLTAGE.
Line 58: Line 58:
 **4. Beam Transport** **4. Beam Transport**
  
-a. Tune beam and send it around ​the properly configured Analyzing Magnet+a.      Use the magnet predictor tool and set Quad 1 to the predicted value.
  
-b. You may need to make adjustments to the TERMINAL VOLTAGE dial to get the terminal to the proper energy for transmission ​around the magnet and fairly balanced current on the slits+b. Tune beam and send it around the properly configured Analyzing Magnet
  
-c. When current is present on the LE and HE Slit current meters you may then switch ​the Control Mode to AUTO (middle position) and the SLIT control light should illuminate. ​ If there is instability in slit control you may try raising ​the CONTROL GAIN more.+c. You may need to make adjustments to the TERMINAL VOLTAGE dial to get the terminal to the proper energy for transmission around the magnet and fairly balanced current on the slits
  
-d. When in AUTO control the machine will go back to GVM control anytime the beam is interrupted.+d. When current is present on the LE and HE Slit current meters you may then switch the Control Mode to AUTO (middle position) and the SLIT control light should illuminate. ​ If there is instability in slit control you may try raising the CONTROL GAIN more.  If the slit currents are not balanced when in slit control, make slight adjustments in the CHARGING VOLTAGE to balance the slit currents. 
 + 
 +e. When in AUTO control the machine will go back to GVM control anytime the beam is interrupted.
  
playground/startup.1338560756.txt.gz · Last modified: 2012/06/01 10:25 by carter